Spit Drop-in Anchor
Spit Drop-in Anchor
Description
Substrates
Applications
- Mechanical and electrical services
- Suspension systems (ceilings)
- Cable trays
- Signs
- Hand rails
Product Advantages
- Lipped anchor body version keeps anchor flush (zinc plated only)
- Available in carbon steel and stainless steel A4-316
- Setting tool stamp marks to indicate complete expansion
- Expander slots allow for fast setting and superior performance
- Cone insert that expands the anchor when driven with setting tool and hammer
- Easy depth inspection keeps threaded rod drop lengths consistent
- Retainer lip to keep anchor flush with surface keeping all rods the same length
- Below surface setting for easy patch work
- Higher performance potential with deep embedment setting (non lipped versic
- Shallow embedment
- Visual expansion check with setting tool
- Can be used with all types of bolts, screws and studs
Specification
Drop-in and Grip L internally threaded, hammer set anchors. Flush fix design is pre-set by inserting into the drilled hole and hammering the internal expansion cone inside the body of the anchor using a setting tool.
Body steel S300 Pb NFA 35 - 561, expansion cone FB10 NFA 35 - 053
Grip Stainless Steel
Female, internally threaded, hammer set anchor. Flush fix design is pre-set by inserting into the drilled hole and hammering the internal expansion cone inside the body of the anchor using a setting tool.
Body steel
stainless steel A4 X5 Cr Ni Mo 17 - 12 - 2, expansion cone stainless steel A4 X5 Cr Ni Mo 17 - 12 - 2.
Installation
- Drill the correct diameter hole to the required depth for the Spit Grip selected.
- Clean the hole with a blow out bulb.
- Push the anchor into the hole.
- Insert the relevant Spit expander of the same diameter as the anchor until it makes contact with the cone.Use a hammer to drive the setting tool into the anchor - stop hammering when the expander shoulder rests against the anchor or when it is blocked (in hard concrete).
- Tighten to the recommended torque using a torque wrench
Data
| Spit Drop-in Anchor - Zinc Plated |
| Eurocode |
Thread Diameter |
Thread Length |
Overall Anchor Length |
Anchor Hole Diameter |
Min Hole Depth |
Effective Embedment |
Box Qty |
| 050788 |
M6 |
10mm |
25mm |
8mm |
27mm |
27mm |
100 |
| 062040 |
M6 |
13mm |
30mm |
8mm |
32mm |
32mm |
100 |
| 062050 |
M8 |
13mm |
30mm |
10mm |
32mm |
32mm |
100 |
| 062060 |
M10 |
15mm |
40mm |
12mm |
42mm |
42mm |
100 |
| 062070 |
M12 |
18mm |
50mm |
15mm |
53mm |
53mm |
50 |
| 062080 |
M16 |
23mm |
65mm |
20mm |
70mm |
70mm |
20 |
| Spit Drop-in Anchor - Zinc Plated Indicative Tensile Loads in Concrete |
| Thread 0 (mm) |
Embed Depth (mm) |
Torque (Nm) |
Centre Spacing (mm) |
Edge Dist. (mm) |
C20/25 Tensile Load (kN) |
>C20/25 Shear Load (kN) |
| M6 ( x 25) |
27 |
5 |
100 |
70 |
|
|
| M6 ( x 30) |
32 |
5 |
100 |
70 |
2.7 |
1.6 |
| M8 |
32 |
10 |
120 |
80 |
3.4 |
3.2 |
| M10 |
42 |
22 |
160 |
100 |
5.0 |
4.5 |
| M12 |
53 |
36 |
200 |
130 |
6.8 |
8.7 |
| M16 |
70 |
80 |
250 |
170 |
10.9 |
16.9 |
|
